You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 1124 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 7 posts

Sunday, March 20th 2011, 10:58am

by hi.todd

Concur with Mitchco, Orbit timer no bueno!! :thumbsup:


You were lucky to get 3 years out of it.

Friday, March 18th 2011, 10:25pm

by Mitchgo

Unfortunately that doesn't confirm that it's the controller, though in all probability it is
Do you have a multimeter? This would be the easiest and fastest

Though You can try one zone at a time.

Hook zone 1 to port 1 and take out the other 3 zone wires from the controller. Turn it on and see what turns on in your yard. Complete this for each zone, if only a single zone turns on each time then you have no fully confirmed thats its the controller. Try hooking up zone 1 wire to port 4 and turn on zone 1 from the controller, this will confirm it too. Basically the controller is sending power to all the zones at once.

Friday, March 18th 2011, 9:53pm

by kevincheong

This time I tried to swap station connection on the controller, station 1 to station 3 and station 2 to station 4. I still got the same result station 1 on (1,2,3,4 on), station 2 on (2,3 on), station 3 on (2,3 on).

So, this is the controller problem??

Thursday, March 17th 2011, 8:14pm

by Mitchgo

Good job on the diagnosis.

If you have a multimeter you can test the AC power by touching the common port to the zone port while the zone is running. For example, if you turned on zone 1 and used your multimeter and saw that the rest of the zones were getting around 24V as the same as zone 1 then you have 100% verified that the problem is within the controller. Frankly I'm surprised all 4 valves cranked on from this controller without blowing the fuse. So it's possible the issue could be something else such as more wireing issues, master valve issue with stuck zones ( and or manually turned on from the winter) and more with further diagnosis

However I'm leaning to bet on the controller is gone kaput

Your problem is that your controller is Orbit!!!
You have a $20 dollar controller, of course it's going to fitz up.

Please upgrade to a normal professional controller- Hunter , Rain Bird , WeatherMatic , Irritrol

Thursday, March 17th 2011, 6:51pm

by kevincheong

Yes, I am using underground bored water.

Thursday, March 17th 2011, 12:14pm

by mrfixit

Is there a wire hooked up to the pump terminal?

Thursday, March 17th 2011, 1:32am

by kevincheong

Controller or valves problems?

I have a 4 years old controller (orbit 57696) and it is working fine for years. This morning when I turned on station 1 (all 4 stations were on at the same time), tried station 2 (2 and 3 were on), turned on station 3 (2 and 3 were on again), turned on station 4 (2 and 3 were on as well).

I checked all the valves, opened and cleaned them thoroughly. Check the valves wiring everything seems ok. But the same problem still exists. So, I disconnected the wire of station 3 on the controller. Turned on station 3, this time station 2 and 3 were still on at the same time!

What's wrong?? Any solutions to solve this problems? Thanks in advance.

Regards,
Kevin