You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 2647 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 8 posts

Friday, September 21st 2007, 2:50pm

by wingsaircharter

If you read the directions you can put them on with no tools. I just did 20 today on 1" and 1.25" polu and never used a tool. They went on superbly and save tons of time. Now I just hope they don't ever leak.

Tuesday, May 25th 2004, 8:00am

by drpete3

I use robogrip pliers to get them on.

Monday, May 24th 2004, 9:22am

by aquamatic

Blazing Saddles--

The only issue I have had is that you cannot properly seat and install one on the slightest curve on the pipe. It causes a slack and they snap open.

Also as far as installing them by hand- I use channel lock pliers to snap the belt closed

Monday, May 24th 2004, 9:18am

by aquamatic

If your concerned about your water building rust stains on your house or walkways, You can install an injection system that will dye out the minerals that cause the rusting stains. I believe it's called RustIt or something like it. John Deere Landscape sells the product

I hear that the refills are not cheap!!

Monday, May 24th 2004, 8:29am

by HooKooDooKu

I don't think a filter (even a 200 mesh) is going to help prevent "MINERAL" build-ups that would be caused by HARD water. But if your hard water ALSO has Sediment, then perhaps a filter is a good idea. Unfortunately, very few people bother with a filter in my area and I found it difficult to find something suitable for installation in a mainline.

Easiest way to go from 3/4" copper to PVC is a 3/4" to 1" male thread adapter.

Monday, May 24th 2004, 8:21am

by BSME

3)You sound pretty handy... im sure you can solder a 3/4'' elbow to the bottom of that copper and solder a 3/4'' wybow into that elbow.. i may not have the best technical talk but you can then just slide 3/4'' poly pipe on that wybow and tighten it with a couple turn clamps since it's main line... assuming your manifold is threaded you can teflon tape a 3/4'' x 1'' combination reducing elbow and screw that into the manifold and clamp the 3/4'' poly on the fitting... again i know i can't speak clearly in writing but that's how i'd do it

Monday, May 24th 2004, 4:13am

by drpete3

I have used blazing saddles on poly that was purchased from home depot and no prbs.

Saturday, May 22nd 2004, 5:51am

by tth

manifold questions

I had a few questions for a new manifold design/installation. This is my first attempt and I wanted to try do things correctly. I purchased the dura pre-assembled manifold, PGV-101G valves, PGP rotars and hunter pop ups, and will be using 1" poly.

(1) Are water filters a good idea for residential connections from the main water line? Our water is hard, and from time to time I need to clean off the sediment on the filters for our indoor faucets.
(2) Should I install an inline drain down stream from each of my valves? (This was suggested in a popular mechanics article in 2002)
(3) I had a plumber come out and install and 3/4" RPZ and he left a copper 3/4" female stub below the ground for the manifold connection. What is the best way to dialate from the 3/4" copper to the 1' PVC for the manifold?
(4) Has anyone ever had any problems with leaking after installing the blazing saddle self tap fittings onto poly pipe from the local hardware store versus commericial grade? The salesperson at the sprinkler supply thought there could be a potential problem due to the difference in thickness of the two types of pipe.

Thanks for your assistance! Great forum [:D].