You are not logged in.


Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 4194 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Friday, July 27th 2007, 1:29am

by Wet_Boots

One foot is deep enough. This is especially true when poly pipe is being pulled over deeper underground utilities, which can be (by code) as shallow as 18 inches.

Thursday, July 26th 2007, 2:20pm

by wiredup

Thank all for your comments.

I think I'll go 18-24 inches; we'll see how the trenching goes tomorrow. I'll try to post pictures.

The ground is hard as nails. I just dug one of the valve box holes and it took me an hour!

Thanks again team!

Thursday, July 26th 2007, 4:58am

by drpete3

It wont fail if you are 8 or more inches under the ground. Pvc will be fine too but just be sure to blow out the system for the winter. I do agree if you think youll dive over an area it should be deeper. the reason i like poly over pvc fro the majority of a system is if for some reason it were to move...heaving of the ground driving over it etc poly is more flexible and will move but pvc can crack. dont get me wrong many systems are 100 percent pvc and are fine.

Thursday, July 26th 2007, 2:53am

by HooKooDooKu


The Water Authority recommends 2 INCHES? (Did you mean feet).

Well here's my input on depth based on my research before I installed my irrigation system.

1. I believe that plumbing codes typically require any mainline pipe (pipe leading to the control valves) not made of metal to be buried to a depth of 18" (as measured from the top of the pipe to the soil level).
2. Deeper is safer (more protected from freezes and potential vehicle traffic).
3. 10" to 12" were the most common suggested depths for latteral lines in irrigation books and (here's his page on pipe instilation: )

I could definitely see where shallow installations fail within 2 years not so much from freezes but because people forget the underground pipes, and then run over them with a vehicle. A simple example I can think of is you purchase 12 bags of mulch for that landscaped area and you load them up in your SUV. When you get home, you realize that if you park at the curb, you are going to have to make 12 trips to haul those bags from the SUV to the landscape area. You decide that it would be a lot easier to just drive through the lawn, drop the 12 bags on the ground, and drive back to the curb. You forget about those pipes, and a shallow install results in broken pipe.

I've never hear of freezing temperatures affecting PVC, assuming there isn't ANY water in it. 32 degrees is just a magic number for water, not PVC.

Wednesday, July 25th 2007, 1:33pm

by wiredup

Thanks Pete--the only thing I'd say is the Leesburg Water Authority said recommended the depth at 2". He said some of the irrigation system don't put them in deep enough and the systems fail within two years.

Do you attribute that to a failure to winterize the system? I guess the next question I'd have is: does PVC fail when it freezes despite being clear of water?

Tuesday, July 24th 2007, 4:52am

by drpete3

I wouldnt suggest going that deep due to mainenance. If you ar that deep it will be harded to work on in the future. Just go 8 inches and make sure you blow out the system before winter.

I would suggest using 100 psi poly for your situation. but it is up to you.

Monday, July 23rd 2007, 12:14pm

by wiredup

Thanks folks--I do happen to be in place where it freezes (Northern Virginia), however I intend to install everything well below the freeze line (12")--I'll go 24".

Monday, July 23rd 2007, 5:28am

by drpete3

the black pipe is called poly pipe and it works very well in climate that freeze but it is not recommended for the main line ie before the valse due to the constant pressure unless you use 160 psi poly. I use 90percent poly.

Monday, July 23rd 2007, 1:23am

by Wet_Boots

PVC in sunlight can have a shorter lifespan, but underground, it doesn't seem to suffer.

Sunday, July 22nd 2007, 9:44pm

by mrfixit

I laugh when I see plumbers working on sprinkler systems. Most of them are clueless. I can't tell you how many times I've had to redo their work. Many many. I vote for white schedule 40 PVC. Let me add I'm in So. Cal where it doesn't freeze. I'd say 99% of all new installation here use white pvc. I did see an all copper system once. Unbelievable! Lateral lines included. Good luck!