You are not logged in.


Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 4277 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Wednesday, March 28th 2007, 2:57am

by Wet_Boots

Hunter ICC has it, for one example. As for the Imperial Valet controllers, I've used them, and liked them. They can be repaired
<center></center>But at this point in time, there might be another direction to take, since you have a new clock already. This would be to upgrade the system with new control valves, if possible. It occurs to me that a system installed in 1959 might not have any backflow protection. On flat properties, a group of valves near the house can be replaced with antisyphon valves. If the valve is at least six inches higher than the highest sprinkler they feed, you have backflow prevention you can count on. This could actually cost you less than having the Imperial controller repaired.

Wednesday, March 28th 2007, 1:36am

by SprinklerGuy

That Imperial was likely repairable...I get them repaired or repair them myself quite often.....what was wrong with it?

Must be Imperial valves as well?

As Boots said, some of the old solenoids will not respond to the newer controllers...I am unaware of any solid state controllers that would be reliable in this capacity.

Tuesday, March 27th 2007, 3:16pm

by jmduke7

Well it was a shot, I am unfamiliar with Imperial. Maybe someone else on this forum is and can give you some insight on this controller.

One thing to consider, if you can't find a controller to handle the load of those old solenoids, you could possibly find a universal solenoid that will fit them and have a much lower inrush current draw. But I think you will do fine by getting a Rain-Bird ESP-4M controller (or Hunter Pro-C if you prefer). Here is the link for you to do some research on the Rain-Bird controller. ( )
Good luck!

Tuesday, March 27th 2007, 2:47pm

by fcovin

It is an Imperial RIVT 6 station...output 24 V AC 60 cycles
transformer capacity 50 VA fuse 3amp whatever any of this means.

Tuesday, March 27th 2007, 2:24pm

by jmduke7

Do you know what model and make it was? I am a fan of the old mechanical controllers. Although they lacked some of the more modern features used in todays controllers, they made up for it in reliability in the end.

If you can post the make and model of the unit, I should be able to tell you if it is repairable or not.

Tuesday, March 27th 2007, 2:07pm

by fcovin

the old timer was installed in 1959...I have no idea if anyone could repair...a real antique.

Tuesday, March 27th 2007, 1:22pm

by jmduke7

The Hunter PRO-C would be a sound choice, but I prefer the Rain-Bird ESP-4M controller. The electro-mechanical controller you had, was it un-repairable?

Tuesday, March 27th 2007, 12:51pm

by fcovin

Wet Boots...would the Hunter that is rated at 1 AMP possibly work

Tuesday, March 27th 2007, 12:49pm

by Wet_Boots

Some old valves can demand a full amp to open the solenoids. No inexpensive solid state controller exists that will operate them.

Tuesday, March 27th 2007, 11:59am

by fcovin

timer control replacement

I recently replaced my old mechanical timer with a Toro ECXTRA...all zones work except one which was working fine before the replacement. My system is very old and a sprinkler technican that came out to inspect said that the Toro timer did not produce enough amperage to open up some of the older solenoids. Any thoughts and if I should replace the Toro and if so, any recommendations, ie, are there units that have more. I notice that the Toro has a .3 amp output and that a Hunter has a 1. amp output...thanks