You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 2934 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 3 posts

Tuesday, November 14th 2006, 10:25am

by HooKooDooKu

The 11GPM sounds pretty high for a static pressure of only 50psi. I don't question that your hose bib can't fill an 11 gallon bucket in 1 minute, but if you design for an 11gpm system, I think your going to have an inadiquate design.

A quick look at one of those "short cut" guides indicates that for a 5/8 meter, 3/4 copper water line, and 50psi static pressure, you shouldn't design for more than 6GPM.

However, if you tie directly into the water line just after the meter you might find that you've got more than just a 3/4" copper line. In my case, I found that my water line from the meter to the house was a 1" PVC. The PVC then converts to 3/4" copper just before it enters the basement (building codes prohibit PVB for exposed pipes). Should you find this to be the case, you'll be able to design your system for 8GPM (or a little more) and won't have much of a pressure drop in the house when the irrigation system is running.

Additionally, tying in to the water line as close to the water meter as possible will help reduce your pressure losses. You might have 50psi static pressure, but once water starts flowing through those pipe, friction losses will eat away at that pressure. The more pipe the water has to run through, the more the presure losses. And starting with only 50psi doesn't give you much breathing room. When the final system gets up and running, your going to lose 2-3psi through the meter, about 3-5psi through control valve, you're going to want at least 20 (and more like 30) psi at the sprikler heads, so that leaves as little as 12psi of pressure loss available for friction losses and through the BackFlow. In the range of 5-8GPM flow rate, you'll lose 1-1.5psi for every 100' of 1" pipe PVC pipe (3-4 psi if you use 3/4" PVC). The backflow can likely eat up another 3-5psi. And if your area requires an RPZ for backflow, that's going to be about a 15psi pressure loss.

Friday, November 10th 2006, 11:33pm

by Wet_Boots

You only do a hose bib connection if have no other practical choice. The only forseeable positive for not making a standard connection is if the system is poorly designed, and not operating with enough pressure, whereupon additional flow can be obtained by trading the hose bib supply for a proper one.

Friday, November 10th 2006, 11:14am

by kgr

Hose bib

I'm sure you are all getting tired of hearing from people who want to hook their sprinkler systems from their hose bib. But my question is: I can get 11 GPM out of my hose bib in my front yard. I have a 5/8 meter in my front yard. A 3/4 inch copper pipe enters my basement and the bib is tied off of that with only 2' of 1/2 copper. Am I going to be that much better off if I make a new poc of the 3/4 and then pipe it outside or will the 11 GPM hose bib work in this case. I do not have a pressure regulator and my static pressure is 50 psi. I do relize that I will install a BFP after the bib.