You are not logged in.


Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 621 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 9 posts

Wednesday, September 6th 2017, 8:55pm

by Stubdaddy

PGP vs PGJ Sprinkler heads

I have a system that uses PGP sprinkler heads. I found a PGJ sprinkler head in my garage. Can I use the PGJ sprinkler head with a system that uses PGP heads? I would like to use what I have if possible. Thanks

Saturday, December 10th 2005, 7:33pm

by toxin

little side-not/addition to what wet boots said. there are 12 normal nozzles that are read with different precip. rates. those grey nozzles are 'low-angle' nozzles for a different trajectory. there are 7 of those nozzles plus one blank nozzle for plugging.

Thursday, December 1st 2005, 7:43am

by Wet_Boots

There are twelve different red PGP nozzles for standard trajectory spray, each with a different flow rate. The 0.9 gpm flow rate is for a #2 or #3 nozzle. Very few installs are done with those smallest PGP nozzles, except for inside corners and/or small areas.

If you have room for heads to spray at least 30 feet, use the PGPs. And do some more reading on them, so you understand them better.

Thursday, December 1st 2005, 4:41am


I was more curious from a design standpoint. I see with the PGP you can use a red or grey nozzle, which has a drastic difference in the flow rate & GMP.

Hunter has the red nozzle listed by default on the PGP, which has a very low flow & GPM. The grey nozzle has a much higher GMP & rate, and is even higher than the PGJ for the same pressure & distances.

As I questioned earlier, by using the PGP rotors, wouldn't you save quite a bit of money by using the PGP rotors. With the GPM requirements being so low it seems you would be able to reduce the number of zones.

Wednesday, November 30th 2005, 3:08pm

by Tom

PGJ heads are designed for 15' to 37' distance

PGP heads are designed for 28' to 50' distance

Wednesday, November 30th 2005, 8:14am

by Wet_Boots

You are ignoring the many nozzle choices that allow you to choose your own precipitation rates.

Wednesday, November 30th 2005, 2:15am


I mainly question why the GMP is so much lower in the PGP than the PGJ for the same pressure and radius.

If this is true, couldn't you save a lot of money by not having to use as many zones since the GMP is so much lower in the PGP. The PGP heads cost more, but not compared to the extra piping and zone valves needed to use the PGJ heads.

Tuesday, November 29th 2005, 11:33am

by RidgeRun05

The PGP sprinkler head has been around since the beginning of Hunter Industries, and has been the foundation of many sprinklers built since then. The PGJ was only recently introduced, because many contractors requested a rotor type head that would cover a smaller area. While flow rates may be similar, depending upon the nozzle used, the PGJ is designed with a smaller radius for small lawn areas, and the PGP is designed with a larger radius for large lawn areas.

Tuesday, November 29th 2005, 3:27am



I assume I am reading the information correctly, but is there really that big of a difference between the PGP & PGJ spray heads? In comparing the two heads at the same pressure (30 PSI) and radius (30') they compare as follows

GMP - 0.9
Rate .19

GMP - 2.5
Rate - .53

In designing my system I am looking at a 50PSI working pressure at 10GPM. To me it seems like I would be better off using the PGP heads since they have a much lower flow rate, but maybe I am missing someting. Am I also correct in that the PGP would have to run at least twice as long as the PGJ to water the same amount?

Why is there such a big difference between these 2 products, and why would you use one over the other?