You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 3150 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 9 posts

Friday, September 2nd 2005, 6:34pm

by Jazzer K

just to be safe and if you have the money I would throw on a 2 hp pump which will get you up to 120 psi and that will do what ever you want it to if you go with 2" main. You could run 15 30ft rotors easy.

Friday, September 2nd 2005, 6:31pm

by Jazzer K

You normally want the main to be same size or bigger to have that constant flow from 1 1/2 " main to 1" feeders to keep the pressure when floe restrictions are a factor, which they always are. I say no.

Thursday, August 25th 2005, 4:23am

by Wet_Boots

<b>harryh</b> - you want to take care to deal with your particular situation. How much uphill are you pumping the water? Each foot of elevation reduces pressure by 0.43 psi. Pond water will contain particulate matter, and you will either have to strain it out, or select equipment that can handle the crud. At sub-30 psi, no sprinkler will give you more distance than a Rainbird Maxipaw, and they will handle crummy water. The Rainbird R-50 also handles pond water, and has unsurpassed coverage at low pressures. Depending on lawn area, elevation, and pump you select, you might do best by expecting less distance from the heads, and lay out the system accordingly.

There are two basic pumps you can use. Most generally useful is a shallow-well jet pump, which gives you higher pressures that most rotor heads need for longer spray distance. Most efficient, from a cost-to-run viewpoint, is a plain centrifugal pump, without any shallow-well injector, which can double the flow for a given horsepower, but at a lower pressure that requires much more careful design for the lower distances the heads will spray.

Wednesday, August 24th 2005, 5:36pm

by harryh

Thank you for info.<blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote"><i>Originally posted by HooKooDooKu</i>
<br />catqua,

Before you just jump into a decision based on one forum message, I'd recomend that you review www.irrigationtutorials.com there's lots of information to better explain in GREAT detail the right way to design an irrigation system.

While you likely will not go wrong using 1" pipe if you're starting with 3/4" (after-all 1" PVC and its associated fittings are not that much more expensive than 3/4"), I feel like you might be jumping into 1" pipe without knowing why.
<hr height="1" noshade id="quote"></blockquote id="quote"></font id="quote"> <blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote"><hr height="1" noshade id="quote"></blockquote id="quote"></font id="quote">

Wednesday, August 24th 2005, 5:28pm

by HooKooDooKu

catqua,

Before you just jump into a decision based on one forum message, I'd recomend that you review www.irrigationtutorials.com there's lots of information to better explain in GREAT detail the right way to design an irrigation system.

While you likely will not go wrong using 1" pipe if you're starting with 3/4" (after-all 1" PVC and its associated fittings are not that much more expensive than 3/4"), I feel like you might be jumping into 1" pipe without knowing why.

Wednesday, August 24th 2005, 5:04pm

by harryh

I have two {2]inch pipe running up from pond 450 feet total need to know what pump i will need to have water at 35 ft spray heads.

Wednesday, August 24th 2005, 3:59pm

by catqua

Thank you HooKooDooKu for your time to respond with great detail. I will be using 1 inch pipe. I have a few long runs in my sprinkler plan. Its such a big job to put a system in so its worth the extra expense. Thanks again

Wednesday, August 24th 2005, 1:06pm

by HooKooDooKu

It can.

The primary reason for expanding to 1" pipe even when your main is 3/4" is to minimize pressure loss due to "friction" loss.

As water travels down a pipe, it doesn't do so perfectly smoothly. It basically "rubs" the sides of the pipe and the net effect is a pressure loss. The amount of pressure loss is a fuction of pipe size and water flow. Based on tables you can find on the internet, here's a couple of examples (assuming all pipe is PVC Sch.40)...

5gpm running through 1/2" pipe for 100 feet will lose about 8.5psi of pressure from one end of the pipe to the other.
That same 5gpm of water running through a 3/4" pipe for 100 feet will lose about 2psi.
That same 5gpm of water running through a 1" pipe for 100 feet will lose about 0.5psi.

Of course the other half of the equation is that with a 3/4" main, you want to limit the flow of your design to about 7gallons per minute per circuit. Otherwise, water will have to flow at what is considered too high a velocity through the 3/4" main. Then your next concern is pressure loss. Your irrigation system is going to lose pressure as the water travels through the water meter, the backflow preventer, the control valve, and the fricsion loss of the pipe. If you design your system using 3/4" pipe, you might find that your system static pressure minus all these pressure losses leaves you only 15psi at your last sprinkler head, but you've purchased a head designed for 25psi. Or if the distance from your first head to the last head is really far (100s of pipe feet), there could be a 5-15psi pressure difference between the two spray heads.

Wednesday, August 24th 2005, 9:07am

by catqua

1 in piping to 3/4 in main????????

is it benifical to use 1 inch piping for my sprinkler system when I have 3\4 inch main??