You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 3405 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 5 posts

Monday, August 1st 2005, 4:58pm

by RidgeRun05

<font color="red">It is important to turn off or close the water main and drain the irrigation line completely before disassembling a valve. Open the bleed screw on the top of the valve to relieve any remaining water pressure.</font id="red">

To disassemble the valve, depending on make and model, first you must unscrew the solenoid from the valve (make sure water is off). Once the solenoid is removed, simply remove the screws on the top of the valve, or if it is a jar top valve, simply unscrew the whole top of the valve. (Note, if you have metal screws on top of the valve, it is NOT a jar top valve. Once the screws have been removed, simply lift the top off of the valve. Fairly easy even for a novice.

Valve repair kits are available that supply the important parts to the unit. Despite the daily hammering and rushing of water through an electronic valve, they are reasonably durable. With proper maintenance and repair, electronic control valves will sustain the integrity of the irrigation design for years.

If you decide not to fix the problem yourself, you are probably looking anywhere from $40-60 an hour labor, plus parts. Generally, a valve replacement shouldn't take more than a couple of hours.

Monday, August 1st 2005, 5:41am

by cassian

Thanks for the quick responses!!

Fixing control valve with problems like solenoid and diaphragm, is this something that an average Joe can do?? I'm really a novice without any experience with this type of stuff before. If I were to hire a professional to fix this, how much are we talking about?

Sunday, July 31st 2005, 4:02pm

by RidgeRun05

Generally, when the problem is isolated to a single zone, any of the following could be a problem

• No power out at zone terminal
• Cut wire (“open circuit”)
• Shorted wire (“short circuit”)
<font color="red">• High resistance (bad splice)</font id="red">
<font color="red">• Solenoid “shorted” or “open”</font id="red">
<font color="red">• Diaphragm assembly failing</font id="red">
• Solenoid exhaust port completely obstructed
• Flow control on valve shut

The problems in red are the most common causes of single valve failure and is probably the case with your system. Locate the valve and check for the above issues.

Sunday, July 31st 2005, 3:36pm

by Wet_Boots

Probably a failed zone control valve. It needs to be found and fixed.

Sunday, July 31st 2005, 2:39pm

by cassian

Irritrol Double Dial-12 Controller

I've just moved in this house with an Irritrol Double Dial-12 controller installed with 10 watering stations. Everything seemed to be working until this week. I was testing the watering stations manually and discovered that station #8 doesn't work, no water comes out from any of the sprinklers!! What do you think the problem is? All other stations work fine, just one specific station. I'm also assuming that it won't work when I run it during an automatic cycle since it doesn't work when turned on manually. Please help! Thanks!!

Cassian
cassian7@yahoo.com