You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 3380 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 9 posts

Tuesday, April 26th 2005, 3:28am

by sweptwing

I have a nelson smartzone now. About 4 yrs old. I see the new nelson clock (available at warehouse) is about $100 and does have that feature I think? Says from 1 second to 30 minutes delay. What do you think? I need the 12 zone.

Monday, April 25th 2005, 4:40pm

by Wet_Boots

Dollarwise, you may do better getting flow control covers for the valves that need them. I doubt that a 12 zone controller with a programmible pause between stations will be available for less than $200 - it's not a feature I've ever needed, (since I favor the use of flow-control valves) and it isn't found on entry-level models. What is the present controller?

Monday, April 25th 2005, 2:59pm

by sweptwing

Thanks for that. Any suggestions on controllers? Toro, Rainbird? Which ones have an adjustable delay? Thanks again for the info.

Monday, April 25th 2005, 2:14pm

by Wet_Boots

There may be some manufacturing variations in the valves. The only practical solutions are either the flow-control valves, or a new controller with a programmable pause between zones.

Monday, April 25th 2005, 12:42pm

by sweptwing

Ok, I understand that now. Now does anyone have a solution or idea or do I just get a better controller at this point? Also, why did it work just fine on city water and not on a well system with the same pressure and gpm?

Monday, April 25th 2005, 5:40am

by Wet_Boots

In ancient days, there were carburetors on automobile engines, and one would adjust the carburetor flow screw down to the point it would slow down the performance, and then you would back off a quarter turn. A lawn sprinkler flow control valve would be adjusted the same way. The result is no change in pressure, but a valve that will shut off more quickly, because it was only partially open (but far enough) in the first place.

Monday, April 25th 2005, 5:02am

by sweptwing

Like I said, they are brand new to begin with and they are the same ones I used on my last system on city water. What would flow control do for me when I need all the flow I can get anyway?

Sunday, April 24th 2005, 2:47pm

by Wet_Boots

Now you know why they make flow control zone valves. You either need a fancier controller, or new valves (or just the cover assemblies for those Nelsons) that have the flow controls you should have used in the first place.

Sunday, April 24th 2005, 6:43am

by sweptwing

New valves slow to close

I have just installed a new system using nelson 9000 series non flow controll valves. Out of 12 zones, about 5 of them close too slow. I also have a nelson controller that does not allow adjustment of zone change times. Sometimes it switches zones and it takes an additional 20 to 30 seconds to close the last zone resulting in puddling because of extremely low pressure. This is on a well system running 60psi. Any suggestions. Thanks for your help.