You are not logged in.


Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 4920 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Tuesday, June 21st 2005, 12:16pm

by RidgeRun05

Not a problem Dave, if you have any other questions or need anything else, just ask in one of the forums, we would be more than happy to help.

Tuesday, June 21st 2005, 2:20am

by dave37

We are all set. I calculated the PSI and the GPM (what I should have done in the first place) and swictched some of the heads on the sprinklers to 1.5 GPM. It is all up and running at this point. Thanks for the info I really appreciate it and it did help.

Friday, June 17th 2005, 8:46pm

by RidgeRun05

Exactly, your actually causing more problems by have the smaller pipe with the heads on it than good. The friction loss alone is causing a significant drop in PSI. Also, did you flush the lines out before you installed the sprinkler heads. Something to think about just in case you didn't, sometimes quite a bit of dirt can get into the lines during installation. Your solution is probably one that you're not going to want to hear, but I would suggest changing the pipe size.

Friday, June 17th 2005, 2:18pm

by Wet_Boots

Pipe sizing doesn't work that way. Reducing pipe size makes a given water flow move faster, and faster means more friction, and more pressure lost from friction. Find some hydraulic charts to help you figure this out.

Friday, June 17th 2005, 1:37pm

by dave37

My static water pressure is about 77psi and I get approx. 8 gallons per minute. I switched the pipe size to try to increase pressure at the end of the runs. I figured that I have about 250 of pipe on one run, one inch for about 120 feet and the rest (where the heads are located are 3/4 inch pipe. On that zone we had about 5 570's. A couple of the heads at the end of the zone weren't even popping up. We have added another zone and decreased the number of heads per zone. One of the zones has only a couple of rotor heads and seems to be working well. Thanks for the tip about separating head types. Any other suggestions. Should I have not switched the pipe diameter toward the end of the runs? Thanks again for your patience.

Friday, June 17th 2005, 6:52am

by RidgeRun05

Why did you switch to a smaller diameter pipe halfway down the run? What is your static water pressure at the Point of Connection for the system? Generally, but not always, when you are on Municipal water you should have more than enough pressure for a sprinkler system. This is why it is very important to do your homework prior to installation, so you can figure out pipe sizes, the correct sprinkler heads to use, and the amount of heads per zone. A booster pump is probably only going to solve your problems temporarily. Until we know what your water pressure and GPM are though, its hard to say.

EDIT: On a side note, how many sprinkler heads do you have on a zone? Also, generally you want to seperate heads with different flow rates into different zones - IE. seperate large turf rotors from the smallers 570's.

Thursday, June 16th 2005, 2:02am

by dave37

My friend and I have just finished hooking up a 5 zone sprinkler system at my house. My friend has put in a few systems but I have not. We used 1 inch pipe from the end of my house to the other and then switched to 3/4 inch from the edge of my house to the road, about another 75 to 90 feet. I have city water and what I thought was good pressure until we turned the system on. We had a mix of rotor heads and some of the small toro 570's. The bigger heads did not even work so we replaced them with the 570's. I think that we would be better served to get a booster pump and put the rotary heads back on, but we (I) don't know enough about the pump specifics. I know this is loaded question, but does anyone have any suggestions? Thanks.

Sunday, April 10th 2005, 11:05am

by RidgeRun05

You can install a booster pump for your sprinkler system which will boost the pressure thus hopefully solving your problem. What is your static (standing) water pressure? How many sprinkler heads to a zone, and how many heads on a zone? You may also have your city municipality come out and adjust your water pressure, or if you have well water, have the well company come out and see if your well pump is adjustable. Hope this helps.

Sunday, April 10th 2005, 8:25am

by Wet_Boots

Is there a proper backflow preventer in the system plumbing? A PVB or RPZ is wanted, to prevent the return of toxic water into the home. On flat ground, a PVB (pressure vacuum breaker), mounted at least a foot higher than any of the sprinkler heads it feeds, will do the job with the least loss of pressure. You want the plumbing to be right, especially if you're going to sell the house, because you probably don't want to sell it 'as is' unless you don't care how prospective buyers will consider the implied flaws. Once you get the plumbing right, you might post information about the water pressure you have, at no flow, and when a zone is turned on. You can also get a flow rate from the water meter, when the zone(s) are running. There is a 'fix' for you.

Saturday, April 9th 2005, 7:00pm

by TobyKanobe

They are Toro 570s. Lack of planning is my problem, I honestly thought I had plenty of pressure. The system is using 3/4 inch PVC and the valves are Rainbird.