You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 3985 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Tuesday, September 23rd 2003, 10:12am

by aquamatic

To pop it without the tool. Just remove from the housing and lay it on a flat surface standing up. Gently grasp on the threaded grooved cap that goes around the head and pull down.

Unscrew the adjust screw up enough to remove the nozzle and check to see if its clogged.

If you need to replace you can order the same head from SW, you will get the entire head with housing. I wouldnt recommend messing around with wiper seals and bottom seals. The heads are affordable enough to just replace the insert unit

Tuesday, September 23rd 2003, 7:29am

by arpee

Perfectly clear, Pete. Thanks. Any thoughts on how to get the popup to pop up without a Hunter tool? I hesitate to use a pair of pliers for fear of damaging the head itself.

Tuesday, September 23rd 2003, 7:13am

by drpete3

If after exchanging it with another head and the new head works in the old location then I would try replacing the nozzle and if that does not work then I would replace the head.

If after exchanging it with another head and the new head does not work in the old location then you may have a plugged line. Am I stating this clearly?

Tuesday, September 23rd 2003, 1:03am

by arpee

Thanks for the tips--Aqua and RVLI. How do I determine whether I should replace the head? Once I unscrew it off and swap with another--if it works now--does that mean that the nozzle is bad and can be replaced? Would a bad nozzle inhibit popups? RVLI--what if the head is only a couple of years old? Does it mean it can be fixed easily with parts? What are the things that could break on a head?
Thanks guys--I appreciate your patience with my questions...

Monday, September 22nd 2003, 4:15pm

by RVLI

Exactly what aqua said. No need to replace the case if the head's only a couple years old.

Monday, September 22nd 2003, 6:27am

by aquamatic

I would start by swapping the head with another one that is working. You dont have to dig out the whole head if its a Hunter PGP. Just remove some diret around the head until you get to where it connects to the main housing. Twist off the entire head while holding the housing secure. Be sure not to let any dirt drop in the housing.

You can also check the manufacturing date on the top edge on the rim to see how old they are. This will also help determine whether you should just drop in a new head.


Monday, September 22nd 2003, 12:10am

by arpee

Not sure about the pressure inhibiting popup. There is a nozzle in the head (I can see it-red). The other heads prior to the faulty one run just fine. Strong sprays, consistent turning radius. When I manually pulled out the riser on the faulty head, I just noticed that the spray was not as strong or as far a throw as the others. Any thoughts?

How would I go about replacing the head? I don't have a Hunter tool. Do I need one to remove the head? Do the heads simply screw off the riser?

Thanks.

Sunday, September 21st 2003, 4:16pm

by RVLI

Correct me if I'm wrong, but your saying it doesn't have enough pressure to pop up? Is there a nozzle in the head? How to all the other heads run? The same way? Are there nozzles in each of those heads on that zone?

Sunday, September 21st 2003, 10:36am

by arpee

Just checked it again. It is a Hunter PGP sprinkler head. I can manually pull it up from its casing using a pair of pliers, and it rotates, but does not spray with the normal force, and while it retracts into its housing just fine, it will not pop up unassisted.

Does this still sound like a candidate to be replaced? The entire head? Or just the nozzle?

How exactly do I go about replacing it? What does the housing assembly look like? If I dig it up, how far down do I go? How do I unscrew it from its casing? How much of it is a single piece to be replaced? Is there a website that shows me a better picture of what the repair/replacement would entail?

Thanks.

Sunday, September 21st 2003, 8:44am

by RVLI

It would probably be best to just replace the heads, if it is an older system. Most likely the gears in the rotor heads are worn out and should be replaced anyways. The spray heads are probably either clogged or need a new nozzle. All you should need is a spade, or a shovel of some sort. The heads you should be able to turn by hand. You will most likely need an adjustment tool for your gear driven heads to adjust them.