You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 463 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 9 posts

Thursday, May 16th 2013, 8:07am

by Wet_Boots


Thursday, May 16th 2013, 6:13am

by Floridaguy (Guest)

Low pressure all zones

Thanks for the responses! I will try and round some diaphrams up. Didn't see them at home depot, I'll check for online sources. I'll post the results here for future reference.

Wednesday, May 15th 2013, 5:17pm

by Wet_Boots

It isn't that each of six diaphragms has gone equally bad. It's that there isn't any practical way to determine which one diaphragm is the one to replace, in a situation where all these valves are sticking open. In favor of replacing all the diaphragms, is the likelihood that all the valves are the same age, from the same batch, and are going to have diaphragm failures at around the same general time.

Wednesday, May 15th 2013, 10:05am

by mrfixit

Having the diaphragms go bad on all the valves is rare but not unheard of.
I ran across this one time. All 6 of the 711 valves had bad diaphragms. The old 711's and the 205's have the same diaphragm.
I think Boots gave you good advice. I'd look at the diaphragms before the solenoids. Solenoids rarely go bad. To have all 6 solenoids be bad without a lightning strike would be impossible in my book.

If the solenoids are a concern to you, you could buy new 205's and swap out all the parts.
--
As a side note I've never seen a controller cause what you've described.

Wednesday, May 15th 2013, 7:38am

by Wet_Boots

Flow controls on your valves might have prevented this from happening. Figure on replacing the diaphragm assemblies.

Wednesday, May 15th 2013, 6:06am

by Floridaguy (Guest)

low pressure all zones

City water by the way...

Wednesday, May 15th 2013, 6:04am

by Floridaguy (Guest)

low pressure all zones

I have Irritrol valves 205S. Thanks for trying to assist!

Tuesday, May 14th 2013, 5:41pm

by Wet_Boots

We need the make and model of the valves (a photo helps)

Are you on well water?

Tuesday, May 14th 2013, 12:36pm

by Floridaguy (Guest)

low pressure-all zones

Hello,



Been searching the forums, but can't find someone with my exact problem.



I have a 6 zone system. ALL zones are running with about half pressure. My controller is cyceling through the zones properly, and I do have voltage to the solenoids. When I loosen the solenoids almost all the way, I then have full pressure to the sprinklers. This holds true for all 6 zones.



How can I determine if I have bad solenoids, or bad diaphrams? And, isn't a little strange that they all failed at once? ( I havent used the sytem in several months)



What can I check without just throwing parts at it?



Thanks in advance! 8)