You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 2423 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 7 posts

Tuesday, August 28th 2007, 4:04am

by jusme

I'm going to consider this thread closed. Thanks guys very much for your feedback!

Monday, August 27th 2007, 5:06am

by HooKooDooKu

<blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote"><i>Originally posted by Wet_Boots</i>
<br />Buy a threaded brass coupling, and use that. Or use a threaded brass ball valve.
<hr height="1" noshade id="quote"></blockquote id="quote"></font id="quote">

Love that suggestion! Gives you both a shutoff and male-to-female conversion in one step.

Tuesday, August 21st 2007, 2:51am

by Wet_Boots

Buy a threaded brass coupling, and use that. Or use a threaded brass ball valve.

Tuesday, August 21st 2007, 2:27am

by Lakeside

The key is to make sure you thread it right the first time. It's very easy to have the male copper mis-thread into the PVC.

Tuesday, August 21st 2007, 12:40am

by jusme

I think I'm going to head down to the local plumbing supply later this week and see what I can conjure up. If I read your post right then you're saying I go male threaded copper -&gt; female threaded brass -&gt; male threaded PVC. In that case I'll have to see if they make a male/copper -&gt; female/brass adapter. Or even maybe just male/copper -&gt; female/copper.

Monday, August 20th 2007, 6:15pm

by mrfixit

I don't do much with copper at all. I do know about the problem with female couplings though. I avoid that whenever possible. I'll use a threaded coupling then a pvc male adapter. I also know about electrolysis. You shouldn't connect galvanized directly to copper. I was wondering if a brass threaded coupling would be ok. Brass and copper are very similar. Look at this chart.
http://www.assda.asn.au/asp/index.asp?pgid=18533
There's my two cents.
-
I realized about 30 seconds after posting this that duh, of course copper and brass go together. You see it all the time. Pressure regulators, gate valves, ect..

Monday, August 20th 2007, 3:28pm

by jusme

Threaded Copper to PVC

I searched the forums (and the rest of the Internet) pretty thoroughly and I still can't find an answer to my specific question. I had the plumber over last week to replace my PRV and while they were there I had them put on a tee with a ball valve and then a capped nipple for future irrigation provisions. The mainline in question is 1" copper.

I want to start using PVC right at the capped connection, but my problem is the copper to PVC union. I really don't want to start sweating copper pipe, so any solution that doesn't involve that is highly preferred. I don't have the expertise or the equipment to do so. I've seen other people say you can use a "no-hub" coupler between two dissimilar materials, but I can't find a whole lot of information about them. Do they also go by a different name? I've heard that it's a really bad idea to mate female PVC with male copper because of the damage to the PVC, so I'm going to stay away from that. I guess my problem really is that the plumbers left me with a male copper connection (capped, as I mentioned) instead of a female connection. Do these "no-hub" (or similar) couplers work well even if one side of the connection is threaded? I'm assuming they're meant to be used for a slip connection...but maybe not. Does anyone know? Or know of another way to make the coupling without sweating copper or calling the plumber again?