You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 742 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Tuesday, July 10th 2012, 11:04am

by mrfixit

Open the screw farther. Not the solenoid but the bleeder screw. Take it off if need be.
If it still doesn't come on try tapping on the valve with something to unstick it.
If none of that works look for a shut off valve for the front yard.
I suppose there could be two bad diaphragms.
Simple to change on that valve.

Tuesday, July 10th 2012, 8:31am

by GatorGuy

You're right.
The wire won't affect manual operation.

Tuesday, July 10th 2012, 8:26am

by TexasPenny (Guest)

Guys I can't tell you enough how much I appreciate your help. I am going to try to inspect further for pipe damage of some sort. Also, if a wire was cut and not sending any power to the valve, would that affect my ability to open the valve manually. Since I can not open it manually with the bleed screw, I kind of ruled out a damaged wire. Maybe I was wrong in assuming that?

Thanks

Tuesday, July 10th 2012, 8:21am

by GatorGuy

"....wouldn't the water surface and runoff somewhere..."
Yeah but water is funny. First, the broken pipe could be far from the valve.
Second, and my favorite, is that water will show but it doesn't care where.
I've had water from a broken lateral run down a slope under the sod and show up 25+ feet from the break.
A few months ago my neighbors main line to the house cracked and the water showed about 10' from the meter.
It was broken about 1' from the meter.

Start someplace you know. Backflow maybe. Walk probable path of pipe. Take a long probe, like a 3/8" piece of rebar. if nothing is obvious probe the soil as you go, looking for soft spot.

It's also possible the pipe isn't broken but clogged or collapsed. I just did a repair where the drought shifted the soil enough that the walk to the front door settled. The concrete settled down on a main line and pinched off all but 1/3" of it so we had almost no flow.

Tuesday, July 10th 2012, 5:00am

by Wet_Boots

maybe a wire outside got cut - no electricity going to the valves

Monday, July 9th 2012, 10:27pm

by Texas Penny

After my last post I looked up pictures of the valves and discovered that mine does not have flow control. I haven't seen any signs of broken pipes. This may be a dumb question, but if there was a broken pipe somewhere, wouldn't the water surface and runoff somewhere when the station was turned on at the timer? There hasn't been any construction or digging on my property. Thanks for the help.

Monday, July 9th 2012, 9:36am

by GatorGuy

PICTURE OF DV VALVE WITH FLOW CONTROL.
Extra knob in middle = flow control.
You may/may not have it.


No signs of broken pipes anywhere?
Since you can't find 2nd valve we can' tell if it's on same line or not.
Any recent construction/digging?

Sunday, July 8th 2012, 10:37pm

by Texas Penny

I have Rainbird valves. I believe they are the DV series valves. I've tried turning both the bleeder screw and the solenoid itself. I turned them counter clockwise until water is barely shooting out of them, and the heads on this zone do not come on. Can you tell me more about the flow control. Is there something else besides those 2 things that I need to turn? Those were the only 2 that I found. PS thanks for your help so far.



Oh and I have a double check valve on the main line. Both valves are open. There aren't any other shut off valves that I can see.

Saturday, July 7th 2012, 7:42pm

by mrfixit

Maybe the flow controls are turned off. Off = all the way clockwise.
Maybe there's a shut off valve for the front yard somewhere turned down.

Saturday, July 7th 2012, 5:58pm

by Texas Penny

2 valves stopped working, will not turn on manually either

Hello all,

I have a system with 5 stations. Recently when I went to turn the system on, something weird happened. The first 2 stations that control the front yard did not work. The timer would count them down as if they were working, but no water comes out of the heads. Then, when the timer gets to station 3 for the side yard, it works perfectly for stations 3, 4, and 5 (4 & 5 are in the back yard). I have only been able to locate 1 of the 2 valves in the front yard, but on the one I did find, I attempted to turn it on manually. When I did, I turn the bleeder and the solenoid itself until water seeps out, but the heads never came on. I am at a loss as to why I cannot turn them on manually. Also, I don't understand what could possibly cause 2 stations to not work at the same time. Any help would be appreciated. Thanks.