You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 791 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Friday, June 29th 2012, 10:14pm

by skintdigit (Guest)

Thank you, Wet_Boots. I've just been browsing the site and came upon the detailed description of the various cross-connection prevention devices here:

http://www.sprinklerwarehouse.com/articles.asp?id=187


I'll let my neighbor know about the recommended upgrade. I thought I was going over there to plug in his timer or replace a solenoid. Now I know a lot more about irrigation than I ever dreamed I would. Not quitting the day job, yet, though.

Thank you!

SD

Friday, June 29th 2012, 10:03pm

by Wet_Boots

your AVB is something of an imposter - a lot of them get installed where a PVB should be

the actual approved application of the AVB is one for each zone, downstream of the zone valves

Friday, June 29th 2012, 9:39pm

by skintdigit (Guest)

Thank you. The order of devices you've given makes sense. I was surprised to find the master zone valve upstream of the AVB, because it seems logical to have the cross-connection prevention device as the first device in the chain after the main system shut-off. My question was about the differences and advantages of a PVB over an AVB.

SD

Friday, June 29th 2012, 8:29pm

by Wet_Boots

the preferred order of pieces in the water chain is PVB - master valve - zone valves, because it is best to have the PVB pressurized 24/7

Friday, June 29th 2012, 7:19pm

by Central Irrigation

The benefit is keeping your and your neighbor's drinking water safe to drink. And, yes it should be done by a licensed professional.

Friday, June 29th 2012, 3:44pm

by skintdigit (Guest)

wiring snafu

OK, what is the benefit....reliability? Is that change something that usually requires permitting by a licensed irrigator?

SD

Friday, June 29th 2012, 10:47am

by Wet_Boots

You should complete the repair picture by replacing the atmospheric vacuum breaker with a genuine Pressure Vacuum Breaker.

Thursday, June 28th 2012, 9:22pm

by skintdigit (Guest)

Wiring snafu

Wetboots, thanks for your thoughts on the wiring foul-up. Yesterday, I took a shovel and dug some more around the vicinity of the valves I had traced earlier...scraped off the lava rock and pulled back the plastic liner. Found the master and all four zone valves close together. Not quite a manifold arrangement, but they were close. Master valve was upstream of the AVB and had a very corroded solenoid. Manually turned on the master to verify flow to the AVB loop. Based on the low resistance readings above, I thought that wires #2 and #6 might be the master control and common. Cut the wires at the master and used a 9v. battery to verify. Sure enough, #2 was the common and #6 was the control wire for the master. Once I had the common and master verified, I just used trial and error to locate the remaining wires in their proper terminals on the timer. Had my son help listen for clicks at the solenoids. Still have a couple of valves that are sticking open, but the master is shutting off now and we'll get the others sorted out with new parts or a cleaning shortly. These are old Rainbird valves, round cover, roughly 4" in diameter on 1" pipe. Single thumbscrew on the top center with a bleeder in it and a metal rod attached....about 2 1/2 inches long. The wiring was all red, no white wire to identify common. I hope this thread might help someone else who might encounter a fried valve solenoid and fouled up wiring at the same time, as we did.


Thanks again, Wet Boots!

SD

Tuesday, June 12th 2012, 4:52am

by Wet_Boots

You can always work backwards by connecting a battery to the wires in the field, and checking the controller wiring for voltage

Monday, June 11th 2012, 9:51pm

by skintdigit (Guest)

I thought the same thing, Wetboots. So before I left I attached both 2 and 6 to the common terminals(there are two on this controller) and hooked the others to the zone terminals, then cycled through manually one by one....still no water to the AVB :( .

skintdigit