You are not logged in.


Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 2422 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 8 posts

Sunday, April 29th 2012, 5:20pm

by Wet_Boots

Of course, I should mention that a boiler drain at an outdoor low point needs to be an "old-school" model with a large opening, which is not a thing you can get unless you specifically look for it, and even that won't help if there is any plastic plumbing between it and the basement. Heat conduction is the thing. Houses radiate heat, and basement warmth works its way into outdoor copper plumbing.

Sunday, April 29th 2012, 3:00pm

by Central Irrigation

The problem we find is that even with a 3/4" drain outside, it can freeze closed and still cause damage. I see it more often when the home owner installs a boiler drain in place of the plug.
We install our backflows with a T below the backflow with a 3/4" blow out fitting. Remove the plug and drain everything outside. We do blow through the backflow. Now, before anyone jumps on me for it...99% of our backflow and plumbing repairs are due to hard water build up, leaky shut off valves, or blow outs scheduled to late. I just repaired a Febco 765 that had 15 years of hard water build up on it, that only needed a cleaning and an O-ring. It's been blown through 15 times.
I've been toying with the idea of adding a basement drain to the installs, but the 1% of the 1% that need one, doesn't justify the time. A good service tech. can tell when a shut off needs replacing. And a homeowner should realize that icicles hanging from the backflow is not a good thing.

Sunday, April 29th 2012, 12:01pm

by Wet_Boots

I always wanted the drain to be outdoors, with a supply pipe exiting the basement above grade. That way, a drain could safely drip all winter, if need be.

Sunday, April 29th 2012, 11:15am

by Central Irrigation

Does the pipe exiting the house "elbow" up into the backflow, or does it have a "T" that needs to be plugged? Regardless, both styles of plumbing, like wetboots stated, should have a drain in the basement. The elbow style always has a drain, the T style rarely does. In any event, the technician either forgot to drain back into the basement, or the shut off valve is allowing water to weep past it. Or, he drained it, closed the drain, and the weeping shut off valve refilled the line.

Sunday, April 29th 2012, 10:16am

by Wet_Boots

Even with a replacement shutoff valve installed in the basement, it is always best to work from a standpoint of not trusting the shutoff valve to be 100 percent effective, and to have an open drain in a low point to allow water to drip out before it gets into the expensive parts of the outdoor plumbing.

Sunday, April 29th 2012, 9:07am

by Central Irrigation

Might also be time to replace the shut off valve in the basement as well. Especially since this happened a few years in a row.

Sunday, April 29th 2012, 8:52am

by Wet_Boots

Follow mfr instructions for winterizing and this sort of thing does not happen.

Replace the ball valves.

Saturday, April 28th 2012, 6:17pm

by Twinsmom930 (Guest)

Cracks in ball valve handle section....(both)

I was talked into letting me leave my back flow outside during winter..........turned it on an I have cracks on the side of the bal valves on the side, spraying water out the side. need to replace both, an also water started pouring out the bottom release, will this stop when I replace the two handle section ball valves? Paid the last 2 years to have the back flow rebuilt! Wilkins! Please help.......trying to say an do it :(