You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 1172 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Thursday, October 6th 2011, 12:13am

by Mitchgo

I agree fixit...

I've never had an inspector fail a sprinkler system... and in most cases they've left it completely alone.. in about probably 40-60% of the cases the homeowner is simply trying to do the 'right' thing...but don't over do it.

Other times it's left in dis-array...

Interestingly enough though stats state a sprinkler system can add 1-3% of value to the property up here.

So a check valve down stream of a stink ugly avb valve above ground ... far from the list of priority...

Again if it happens.. Big whoop just fix it

Tuesday, October 4th 2011, 5:49am

by mrfixit

If you're worried about the wrath of God bury it underground.

Monday, October 3rd 2011, 9:17pm

by Mitchgo

If its only one head which sounds like the last head in the zone. And the rest of the heads are spraying fine. Sounds like a clog to me. You may have to dig the sprinkled headvup back to the end of the pipe run - cut the pipe and flush

Monday, October 3rd 2011, 8:50pm

by Wet_Boots

You're the home owner. Do what you want.
Of course, you might want to someday sell the house, so it makes sense to follow the plumbing codes, so that it passes inspections. The codes prohibit adding any other valves downstream of the antisyphon valves.

Monday, October 3rd 2011, 7:54pm

by mrfixit

You're the home owner. Do what you want.

Monday, October 3rd 2011, 5:00pm

by Wet_Boots

You do not tinker with the plumbing downstream of the antisyphon valves. No check valves. No electric valves. No shutoff valves. These edicts are etched in stone. If a head is higher than your antisyphon valves, lower it, or raise the valve. If the small amount of water escaping the vacuum breaker is a problem, then you change the grade so that the water drains away from the valves.

This is all very simple stuff. No need to make matters complicated.

Monday, October 3rd 2011, 3:23pm

by underdown

That's a good idea about a spring loaded check valve, if this is an ongoing thing I will do that. I assume I could then redirect the back flow water to somewhere preferable.

No, the valve does not leak when they are running, it is only after I turn it off that water comes back up.

And yes, I believe I turned the water back on all the way, never hurts to double check though.

I have tried a few sprinkler heads, one of them was brand new.

At the moment there is only one sprinkler head on this line (one of the large rain bird maxi rotor canister types). I am guess there are more connections, they were just covered up. I have a large bed of gravel covering where I think the rest of the line is.

I like your idea to cap off the sprinkler head, and turn the water on, then wait for a complete break. I bet I could then uncap the line, and see a total loss of preassure, indicating a complete break. Then I could know for sure and start digging up the gravel and then dig up the line. Does anyone want 1-2 tons of free gravel ;)

Monday, October 3rd 2011, 2:39pm

by Wet_Boots

If the only drainage is when the zone shuts off, then it might be the spring-loaded heads pushing water back to the source. No big deal.

Monday, October 3rd 2011, 2:12pm

by mrfixit

That's a lot of drainage but it happens. Your sprinkler line must be higher up in elevation than the valve. You could install a spring loaded check valve right after the valve to eliminate the drainage.

Look at the seals of the sprinklers. Do they leak a lot when the sprinklers first come on? Do they leak when the sprinklers are on? That could be the problem as well. New sprinklers may elimate the problem if they do.

Try turning off one sprinkler at a time while it's running to see if that last sprinkler pops up.

Did you turn the water back on all the way after changing the valve?

Make sure the valve's on all the way via a flow control if there is one.

I've been known to turn off the sprinkler heads to make a break in the pipe surface more quickly.

Monday, October 3rd 2011, 12:59pm

by Wet_Boots

Close off the heads, and run the zone, which forces water out of the break.