You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 1278 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 10 posts

Wednesday, April 20th 2011, 12:25pm

by wsommariva

I installed a new brass PVB this morning and no problems. I ran the system twice to test and no PVB issues.

Thanks for all the help.

Monday, April 18th 2011, 8:46am

by wsommariva

I know. The old one was plastic, that's why I bought a brass one. I think all issues have been resolved and I don't expect problems. I removed the auto drains yesterday.

Monday, April 18th 2011, 6:30am

by Wet_Boots

A new PVB may be as likely to dump water as the present one. The remedies have already been detailed.

Sunday, April 17th 2011, 4:45pm

by wsommariva

This project is my never ending one. But I'll end up with a great, although small system. My new PVB comes on Tuesday, once installed that should be the end of it. I'll let everyone know how it turns out.

Sunday, April 17th 2011, 9:34am

by hi.todd

We have all been there!
Each time we learn the sprinkler knowledge it usually costs money and time.
We appreciate your learning as we did, the Hard way!

:thumbsup: :thumbsup:

Thursday, April 14th 2011, 3:48pm

by wsommariva

I bought everything from Toro.com. Homeowner residential products. I do have 3/4" valves. I had just one problem with the PVB, it freaked me out and asked for help here. I don't think it's the PVB, it was my lack of knowledge.

I bought a new brass PVB. I'll put it in, remove my auto drain valves and test the system. I'll let you know if I have any problems.

Thursday, April 14th 2011, 3:08pm

by Wet_Boots

Toro does make flow-control valves. If by some chance you used the 3/4-inch valves that are sold in home centers, you can't upgrade them. Only by throttling down a valve's flow control do you greatly improve its closing speed.

-

Is this all home center equipment? Does the PVB spill every time you turn on a zone? Does it spill only when you cycle from zone to zone? There is a possibility you can deal with the latter by way of controller programming.

-

Nothing you have posted indicates the problem is the PVB. Any PVB will spill when the pressure drops low enough. For what it's worth, the Wilkins 720 is far more likely to reseat itself after a temporary pressure drop. But if you make the system function properly, you don't have those pressure drops in the first place.

Wednesday, April 13th 2011, 7:46am

by wsommariva

Ok I think I'm all set. If I have any problems I'll let you know.

Thanks again for the assistance



EDIT: Toro doesn't not have flow control valves. The valves I have are "low flow" valves. "closes at low flow, ideal for drip". "operates as low as .5 GPM" Can I stick with these valves and see if they work with the new PVB?

Wednesday, April 13th 2011, 7:30am

by Wet_Boots

Take care of the zone valves first. Leave the PVB for last, if it all. No problem combining different makes of valves and controller. Once you have things so a zone opens without spillage from the PVB, you then see that you can run through a cycle without any spillage. You might still have to remove the drain valves.

-

If you want to make all this into a "learning moment" you can get a pressure gauge and connect it to the supply, and observe pressures during operation.

Wednesday, April 13th 2011, 6:34am

by wsommariva

OK I'll put in valve controls put in a better PVB and I should be ok. Is it one control per valve or can I get a one control for all 3 valves?


EDIT.....I need new valves with built in flow control. Will rainbird valves work with a Toro timer?