You are not logged in.


Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 4671 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 6 posts

Sunday, September 4th 2005, 11:11am

by RidgeRun05 - This is a great site for getting started planning a proper irrigation system. I think you'll find some useful advice there. As for the same flow rate out of the sprinkler heads, just use the same size nozzle in the head. The radius won't have anything to do with the amount of water output.

Sunday, September 4th 2005, 8:56am

by Pdross

I just tried your suggestion. The flow on the Toro meter read a steady 7.5 GPS while and the pressure gauge on the well tank dropped from 55PSI and leveled off at 40PSI. When I turned on a second outside faucet (and kept the first running)the pressure dropped to about 20PSI but I was pumping about another 5 GPS. There is a 1/2" pipe to these outside faucets but I plan to connect my irrigation system to the 3/4" pipe coming from the well pressure tank. Can I safely assume that the pressure will stay pretty much the same while the GPS will increase somewhat? I plan to use the Hunter PGP Arc Rotors - some running at 180 degrees and others at 360 degrees. Can I adjust the ones running at 180 to spray half the amount as those running at 360 (so I have consistent watering across both areas)? If so I can finally figure out how many rotors I can handle in a zone. Thanks again for your help. I think I'm pretty close to understanding this now.

Sunday, September 4th 2005, 7:35am

by Wet_Boots

Better to just read the gpm at the Toro device, and go back to the well tank to read the pressure there. If the pressure switch is set for a 20-40 psi operating range, you could adjust it to raise the shutoff pressure to 50 psi or higher.

Sunday, September 4th 2005, 6:16am

by Pdross

When using the Toro flow meter, the "static" pressure dial dropped to zero when I opened the valve (wide open) to measure the GPM. If I closed down the valve a bit I was able to register something on both dials (eg: 20PSI, 5.5GPM). Maybe I am using the meter incorrectly. Is there a way to adjust/increase the pressure from the submersable pump (or the pressure tank in the basement)? Our well is about 100ft deep.

Saturday, September 3rd 2005, 8:04pm

by RidgeRun05

40 PSI is on the very low end of operating an irrigation system. Especially if you take into consideration the friction losses for a backflow device, pipe, valves, and any other component which reduces the water pressure. I am not sure I am understanding your math correctly. You are saying you are flowing 7.5 GPM at 0 PSI? that is not possible. In order to flow a GPM, you must have some type of water pressure.

Saturday, September 3rd 2005, 7:43pm

by Pdross

Calculate Sprinkler Capacity

I used the Toro pressure and flow gauge to determine static pressure and flow of my system. I connected this to an outside water spigot. I have a well (with a submersed pump)- that has a 3/4" copper pipe coming from the pressure tank - and then 1/2" pipe going to my outside spigot. When tested, the static pressure was 40psi. I was only able to get 5.5 gpm at 20psi - and 7.5gpm when it was fully opened (and 0 psi). I plan to connect the irrigation system to the 3/4" pipe - and go to 1" poly pipe after the values to the sprinkler heads. Right now I have the heads placed 30' apart - there are 5 zones - each zone runs about 100' - total area about 120' x 90' - flat. 3 questions: Do I have enough water flow for an irrigation system? How much will my gpm increase if run off the 3/4" pipe? Should I connect the irrigation system before or after the pressure tank? Thanks for any help!!