You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 1567 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 6 posts

Wednesday, April 7th 2010, 8:07pm

by hi.todd

After you repair it? or Reinstall it it should be tested by a Licensed Backflow inspector to insure proper function. Basically you are checking to make sure the air inlet valve opens at 1.0 PSI or greater and that The Check Valve holds at 1 PSI or greater.

With out Differential Pressure Gauges you can not inspect the backflow device.

Good Luck :thumbsup: :thumbup:
Warming up in Houston

Tuesday, April 6th 2010, 6:39pm

by Plumber Joe (Guest)

Removing Plastic Bonnet from Wilkins 420 Vacuum Breaker

After a hard freeze Wilkins Vacuum Breaker began to leak. I unscrewed the top of the cap, then tried to remove plastic bonnet. I finally was able to use a strap wretch to remove the bonnet turning counter clockwise, although there is NO threading on the bonnet cap or brass main body. It just takes a little elbow grease, then you will be able to insert the rebuild kit.

Tuesday, February 6th 2007, 2:01am

by SprinklerGuy

Ditto what wetboots said....


Monday, February 5th 2007, 6:41am

by Wet_Boots

I think the bonnet on a 420 just unscrews. Of course, if you cracked off the top half by letting water freeze in it, the remainder will be difficult to remove. Save yourself some grief, and just replace the whole thing, and set up the plumbing so that you can drain all the above-ground pipe and valves.

Sunday, February 4th 2007, 6:29pm

by HooKooDooKu

Step #1: Turn off you Caps Lock. Doing that usually denotes shouting, and it's very difficult to read.

Step #2: If you don't know enough about a PVB to know how to open it up (not that I do, as I've never messed with a PVB), perhaps you shouldn't be trying. I know that's not really any help, but my real point is perhaps it would be easier to just replace the entire unit. After all, if it's been damaged by a freeze, it might be more than just the guts that now have a problem, the entire unit could be cracked or bent such that replacing "guts" might not fix the problem.

Sunday, February 4th 2007, 10:51am

by JA95606

PRESSURE VACUUM BREAKER WILKINS MOD_420

MY NAME IS JOHN CARR, I RESIDE IN LAS VEGAS, NV. A MONTH AGO, (JAN) IT WAS VERY COLD FOR ABOUT A WEEK OR SO (BELOW FREEZING AT TIMES). ANY WAY, DUE TO THE EXTREME COLD, WE DECIDED TO TURN OUR SPRINKLER SYSTEM OFF UNTIL IT WARMS UP SOME (FEB). WE CAME HOME ONE NIGHT, AND UPON ENTERING THE GARAGE. WE NOTICED THE PRESSURE VACUUM BREAKER (JUST OUTSIDE OF GARAGE) WAS SPEWING WATER. SO I TURNED IT OFF AT BOTH VALVES, AND IT STOPPED. WELL, NOW IT'S FEB, IN THE 70'S, AND I NEED TO REPLACE (I GUEST) THE GUTS INSIDE TO PREVENT IT FROM LEAKING. THE PROBLEM I'M HAVING IS, I CAN'T REMOVE THE PIECE INSIDE TO TAKE IT OUT. IT STATES ON TOP "DO NOT USE A SCREW DRIVER TO REMOVE." I'VE TRIED TAPPING ON THE PLASTIC, HOPING TO LOOSEN IT, NO RESULTS; I'VE TRIED TAPPING UNDERNEATH WITH SCREW DRIVER, AND HAMMER, NO RESULTS; I'VE EVEN TRIED USING A LARGE SET OF PLIERS TO EITHER PULL, OR ATTEMPT TO TURN, WITH NEGATIVE RESULTS. WITHOUT DAMAGING THE BONNET OR POPPET ASSEMBLY HOW DO I REMOVE IT FROM THE PRESSURE VACUUM BREAKER?
PLEASE HELP ASAP,
JOHN