You are not logged in.


Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 3587 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 7 posts

Friday, May 29th 2009, 7:32pm

by zendog13

Faulty Diaphragm

Used the bleed screw test. Other two worked fine. So that's the culprit.

Since I'm on a budget, I need to do this on the cheap. If I can simply buy a new diaphragm and swap it out, that's for me.

Question is, where do I find these parts? Is this a big-box item or a specialty store. I'm in LA, so there's plenty of both.

Finally, if I take this route, am I in any way asking for trouble down the line? (In other words, am I being too cheap?) Would a whole new valve assembly be the way to go?

And thanks to everyone that's helped me figure this out. You guys are the best.

Friday, May 29th 2009, 4:38pm

by Wet_Boots

You might just want to buy a new valve , and get a diaphragm assembly along with the bonnet and solenoid. The little grey/black 'button' is the manual bleed. Gently unscrew it, and water will escape and allow the valve to open manually, assuming the diaphragm assembly is in good shape.

Friday, May 29th 2009, 2:56pm

by zendog13

Getting Closer

Thanks for the tip!

So the water is NOT gushing.

So, can I replace the diaphragm on this model? Does anyone know? Should I try swapping out the solenoid again just for kicks?

What's the smartest move here for the long run?

Friday, May 29th 2009, 2:31pm

by mrfixit


Hey Zen, I don't know exactly what whooshing is so if you can't find a break I suspect the diaphragm. When the diaphragm goes bad the valve sounds different. You could unscrew the cap, the part on the right in your picture and turn the valve on to see if water gushes out like it should or just trickling before you buy parts. You might want to just buy an inline 205 and swap out bonnets if you don't want to cut and glue replacing the whole valve.

Friday, May 29th 2009, 11:33am

by zendog13

Gimme a Break

A break is what my logic is telling me as well. After hours of running, I've yet to find the
location, but the tragedy is that the likely place is under a newly
installed stone patio! (How screwed will I be then!)

One question though: what about the "whooshing" sound at the valve?

None of the others do that. Is that something that would be caused by a break further down the line?

Here's a picture of the valve. Like I said, Richdel 3/4". I don't see a model number anywhere. I don't know if you can see it, but there are a few drops on top of the solenoid that just appeared after start-up. The noise is pretty fierce. Wish I could upload audio.

Friday, May 29th 2009, 6:36am

by Wet_Boots

Look for a break. Valves can always be opened manually, without using the controller. For advice on valves bring back some photos of the problem valve.

Thursday, May 28th 2009, 11:45am

by zendog13

Valve Mystery

Okay, here goes.

Five years ago we bought a house w/ a 3-zone Richdel system. The analog controller is so old I think it was once used by Moses.

We turned the system off when we bought the place and waited until we could turn our attention to the back yard landscaping (after 5 years of interior refurb...another story).

In first attempts to re-start, 2 of the three zones are fine.

The third is not working. I don't have a tester, but I rigged a cheap-o activator w/ 3 9-volt batteries. Nothing. Just a kind of rushing sound, like water through a nozzle. (Not really an electrical "buzz" as I've heard described elsewhere.) But no water from the sprinklers.

I did notice that the pop-up heads in that zone were leaking a small bit, and I unscrewed the collar a bit to see that there was at least some water pressure. I cleaned and reassembled that head. Still nothing but a tiny leak. Obviously low pressure.

I even swapped the wiring from another valve. Nada. I even changed the solenoid. Still nothing. Just the rushing sound. I've left the zone running for an hour hoping to find a broken line to explain this, but all I have is the dribble from the heads and a few drops of water on the top of the solenoid and the valve. I thought that might suggest a clog in the valve. However, once I'd disassembled, cleaned and re-assembled the valve, I'm having the same results: whooshing noise, dribble at the heads and tiny leak at the solenoid.

Any ideas? Should I just replace the valve? (While I'm at it, should I chuck this antique controller?) Or is this likely an underground broken pipe that I just haven't found yet? Is it time to call a professional?

Thanks y'all.