You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 2247 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 5 posts

Friday, October 3rd 2008, 8:18pm

by Wet_Boots

If it's a female union end of a manifold fitting, the usual fears of female plastic threads shouldn't apply. It will be the O-ring doing the actual sealing, and not the teflon tape you might apply to the threads.

Friday, October 3rd 2008, 11:43am

by Lowvolumejeff

metal to PVC transition

Yes, there is a tendancy for metal MPT to FPT PVC threded junctions to leak. Biggest culprit is over zealous tightening, causing small cracks in the female PVC fitting. Then, added to the expansion and contraction caused by temperature changes, this is exacerbated and may lead to a leak.

So, I use only MPT PVC to FPT copper or brass.

Boots is a pro's pro. So if he want to reverse the above scenerio, I am confident he can without a leak.

I use 5 turns of teflon tape on every metal to Male PVC threaded adapter.

I like Brass better than copper. I like how heavy it is, and I can use a tool to help me tighten the joint. (Yes, I tend to overtighten a bit, and use a quarter to half turn past maximum hand tightness). Again, I use 5 turns of teflon tape.

I have used copper MPT to a brass FPT faucet or hose bib. I use teflon tape on these.

Hope trhat answers your questions.

And, Boots, I am in Leary Country. :|

Jeff

Friday, October 3rd 2008, 10:19am

by canuck (Guest)

male metal thread in pvc female ok?

You might use a 3/4 x 1 CxMPT adapter, although that might be more expensive.
I've read around on some other plumbing type forums that using a metal male thread into a plastic female thread is not recommended. ?( Supposedly more likely to leak.

Friday, October 3rd 2008, 9:28am

by Wet_Boots

You might use a 3/4 x 1 CxMPT adapter, although that might be more expensive.

Friday, October 3rd 2008, 8:43am

by canuck (Guest)

proper fittings to connect from copper supply to dura swivel manifold

I'm working on a plan for putting a system in at my house and am trying to figure out the plumbing from the water supply to the valve manifold.

Basically I've plumbed from my water supply up and out of my house up through the PVB and then out to a hose bib and down below the ground with 3/4" copper. Now I need to connect to a dura 4 port swivel type manifold. My plan is to solder on a 3/4" copper elbow female adapter. Then use a pvc reducing nipple 1" x 3/4". The 3/4" end into the copper female adapter and the 1" end into the dura swivel manifold.

Is this the right way to do this? Should my female adapter be brass instead of copper? Do I need teflon on the PVC nipple into the female adapter (i don't think that I need it into the swivel manifold since it has an o-ring)? Is there a better way?

Thanks
wb