You are not logged in.


Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 3891 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 5 posts

Tuesday, June 24th 2008, 12:03pm

by mrfixit


Thanks for the picture. I guess I misunderstood what you were saying. I thought you said the pressure at the end of the spaghetti tubing (1/4" line) was 5 lbs.

Tuesday, June 24th 2008, 9:17am

by HooKooDooKu

The only pertinent information I could gleam from a quick review of drip irrigation design at was that the total length of the drip tubing from the point water enters the tubing to the farthest emitter should not be more than 200 feet. Is specifically indicates that adding branches is ok but that the total distance isn't more than 200 feet (so as an example, you could have 400 feet of drip tubing IF the water source connects to the drip tubing at the center). But that doesn't address the issue of pressure loss possibly caused by lots of emitters. The only thing addressed about that is limiting the emitters PER VALVE. But his numbers work out to saying you should limit the system to what is equivalent to 10 gpm. But if you have 10 gpm feeding the start of a 1/2" drip tube, you are going to run out of pressure (so the 10 gpm rule seems to be what to limit an entire circuit likely feeding several 1/2" drip tubes with a 1" or 3/4" pvc).

However, many drip irrigation emitters are (at least some what) pressure compensating. That way, as pressure drops though the tubing (because of distance, friction losses, or hills), the emitters all still release about the same amount of water.

While not explicitly stated at the irrigation web site, I would gleam from other comments I could find that 15psi ios the lower end you would expect to see the water pressure. So 5psi does seem to be a bit low. The person to really take this up with is the ones that designed and installed the system. But before you do that, try testing the emitters and see if it's really making a difference. If you can, put an emitter near the start of the pipe over a pie plate (or any type of catch basin) as well as the last emitter closest to the point you are reading 5psi. If after operating the system for 20 minutes, there is less than a 25% difference between the two, I wouldn't worry about it too much. If there is a 50% difference, then IMHO you have a legitimate beef.

The other thing to try (if possible) is to test the pressure at the START of the line. If the pressure is significantly higher at the start, it might be simply a kinked section of drip tubing.

Tuesday, June 24th 2008, 6:08am

by wxperson

RE: Drip pressure.

Just out of curiosity, how did you measure the pressure at the end of the drip tube? I haven't seen that done.
The "irrigation store" recommended a 3 way connector with a threaded top and compression fittings for the 1/2" line. See the attached photo.
wxperson has attached the following file:
  • pressure.jpg (11.35 kB - 16 times downloaded - Last download: Mar 5th 2010, 7:22pm)

Monday, June 23rd 2008, 8:57pm

by mrfixit

Drip pressure.

Just out of curiosity, how did you measure the pressure at the end of the drip tube? I haven't seen that done.

Monday, June 23rd 2008, 3:33pm

by wxperson

DRIP LINE pressure only 5 PSI

I have a new system, installed by a irrigation company, that includes a few drip lines.. One of the zones has a branch type design which I am skeptical of. The pressure at the end of the line, after several branches, is about 5 psi. I think it is a design problem by having branches off of branches from the main drip line. I cannot find any literature which says "Dont do branches" but have found several sources that show evenly distributed type lines with a closed type feed system as on page 19 of .

What is your opinion on this? I want as much info as possible before I meet with the installer.