You are not logged in.

Reply

Dear visitor, welcome to SPRINKLER TALK FORUM - You Got Questions, We've Got Answers. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

Attention: The last reply to this post was 2258 days ago. The thread may already be out of date. Please consider creating a new thread.

Message information
Message
Settings
Automatically converts internet addresses into links by adding [url] and [/url] around them.
Smiley code in your message such as :) is automatically displayed as image.
You can use BBCode to format your message, if this option is enabled.
Security measure

Please enter the letters that are shown in the picture below (without spaces, and upper or lower case can be used).

The last 7 posts

Wednesday, June 25th 2008, 3:08pm

by drpete

I buy my 300 ft roll at lowes. I like the blazing saddles but my favorite are the dawn t's. I dont see much elsse to comment on in your original post. Nothing wrong with that.

Tuesday, June 24th 2008, 4:33pm

by Roklem

Anybody else with design thoughts?

Monday, June 23rd 2008, 5:24pm

by Roklem

NSF yes, 36 per 100' (108 for the 300' roll, sorry).

Monday, June 23rd 2008, 3:23pm

by Wet_Boots

$36 for a 300 foot roll of 1-inch NSF poly? NSF is the key here, since tubing that meets NSF specs is likely to be good stuff.

Monday, June 23rd 2008, 2:16pm

by Roklem

Thanks, that's kind of what I figured. Any commends on the rest of the design/thought process?

I can get this locally at $36 "Silverline Plastic Corporation Pipe- Poly NSF 100lb- 1in 300ft roll". Any thoughts on that product if I can't find anything less expensive?

Thanks,
Eric

Monday, June 23rd 2008, 1:52pm

by Wet_Boots

The DiG tubing looks like a drip product, and not the tubing used by lawn sprinkler installers. The 'real thing' is too bulky to ship UPS, so you have to get that locally.

Monday, June 23rd 2008, 10:22am

by Roklem

Poly pipe, 60 PSI???

I was getting ready to place a larger order for the majority of my sprinkler system parts on sprinklerwarehouse.com, however I see an issue with the poly pipe. Unforunately when you call thier number, they claim they don't offer any assistance with the products, and their voicemail boxes are all full.

~8 GPM, 3/4 main pipe (5/8 meter), ~40 psi, OHIO

I was going to run SCH40 from the deduct meter inside my house to the backflow (1" PVB) outside, then convert to 1" 200 psi pvc for the mainline. The mainline will be buried at about 10". After the valves, I was going to convert to poly. My issues is, I haven't seen poly anywhere that is 60 psi other than this site. I've tried to find a good source of poly in Columbus at a decent cost without a lot of luck ($40 per 100'). At $16 per 100' the sprinklerwarehouse.com stuff looks good, but I'm concerned about the quality. Even the slighest extra pressure on winterization could blow all the lines. I also planed to use the 1" to 1/2" FT blazing saddles (1/2" male/male threaded adapter to fit all my 1804's with MPRotators), but they're built for 80/100 PSI pipe.

Note, they also list 3.6 GPM as the spec for this 1" poly, so maybe the 60 psi is wrong as well...

While we're at it, anyone see issues with the design I've listed? The only main unresolved issue I have is how/what to install for drains.